1. Supports USB to 8CH RS485, convenient for expanding multiple RS485 industrial serial devices.
2. Supports direct power supply via Type-C port, with reserved 5V~36V DC wide voltage screw terminal for auxiliary power input.
3. Onboard unibody power supply isolation, provides stable isolated voltage.
4. Onboard unibody digital isolation, allows signal isolation, high reliability, strong anti-interference, low power consumption.
5. Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit, lightningproof & anti-electrostatic.
6. Onboard self-recovery fuse and protection diodes, ensures the current/voltage stable outputs, provides over-current/over-voltage proof, improves shock proof performance.
7. Built-in 120R terminal resistor on the RS485 ports, configurable via jumper for flexible switching.
8. LEDs for indicating the power, device configuration status and transceiver status.
9. Rail-mount case design, support stackable combination, easy to install and safer to use.
Parameters:
1. Host Interface: USB
2. Device Interface: RS485
3. Power Supply: USB Type-C (5V) or terminal block (5V–36V)
4. Temperature Range: -15°C to 70°C
5. Humidity Range: 5% RH to 95% RH
USB Interface:
1. Operating Voltage: 5V
2. Connector Type: USB-C
3. Interface Protection: 200mA resettable fuse, isolated output
4. Transmission Distance: Approx. 5 meters
Isolated RS485 Interface:
1. Connector Type: Terminal block
2. Direction Control: Hardware-based automatic detection and control of data transmission direction
3. Interface Protection: 600W lightning/surge protection and 15kV ESD protection (onboard 120Ω termination resistor)
4. Transmission Distance: Approx. 1200 meters (at low data rates)
5. Transmission Mode: Point-to-multipoint (supports up to 32 nodes; a repeater is recommended for configurations with more than 16 nodes)
6. Communication Rate: 1200 bps to 921,600 bps
Indicator Lights:
1. PWR: Red power indicator, lights up when there is USB connection and voltage is detected
2. ACT: Status indicator, lights up green when the driver is detected
3. TXD: Green TX indicator, lights up when the USB port sends data
4. RXD: Blue RX indicator, lights up when the device ports send data back
2. Supports direct power supply via Type-C port, with reserved 5V~36V DC wide voltage screw terminal for auxiliary power input.
3. Onboard unibody power supply isolation, provides stable isolated voltage.
4. Onboard unibody digital isolation, allows signal isolation, high reliability, strong anti-interference, low power consumption.
5. Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit, lightningproof & anti-electrostatic.
6. Onboard self-recovery fuse and protection diodes, ensures the current/voltage stable outputs, provides over-current/over-voltage proof, improves shock proof performance.
7. Built-in 120R terminal resistor on the RS485 ports, configurable via jumper for flexible switching.
8. LEDs for indicating the power, device configuration status and transceiver status.
9. Rail-mount case design, support stackable combination, easy to install and safer to use.
Parameters:
1. Host Interface: USB
2. Device Interface: RS485
3. Power Supply: USB Type-C (5V) or terminal block (5V–36V)
4. Temperature Range: -15°C to 70°C
5. Humidity Range: 5% RH to 95% RH
USB Interface:
1. Operating Voltage: 5V
2. Connector Type: USB-C
3. Interface Protection: 200mA resettable fuse, isolated output
4. Transmission Distance: Approx. 5 meters
Isolated RS485 Interface:
1. Connector Type: Terminal block
2. Direction Control: Hardware-based automatic detection and control of data transmission direction
3. Interface Protection: 600W lightning/surge protection and 15kV ESD protection (onboard 120Ω termination resistor)
4. Transmission Distance: Approx. 1200 meters (at low data rates)
5. Transmission Mode: Point-to-multipoint (supports up to 32 nodes; a repeater is recommended for configurations with more than 16 nodes)
6. Communication Rate: 1200 bps to 921,600 bps
Indicator Lights:
1. PWR: Red power indicator, lights up when there is USB connection and voltage is detected
2. ACT: Status indicator, lights up green when the driver is detected
3. TXD: Green TX indicator, lights up when the USB port sends data
4. RXD: Blue RX indicator, lights up when the device ports send data back









